ISSN 0021-3454 (print version)
ISSN 2500-0381 (online version)
Menu

8
Issue
vol 63 / August, 2020
Article

DOI 10.17586/0021-3454-2020-63-3-242-249

UDC 681.7.068

Digital Format for Preparation of Instrument Production. Part I. Design Stage

V. F. Bulavin
Vologda State University, Department of Engineering Technologies; PhD, Associate Professor


T. G. Bulavina
Vologda State University, Department of Engineering Technologies; Associate Professor


V. V. Yakhrichev
Vologda State University, Department of Engineering Technologies; Senior Lecturer


A. S. Stepanov
Vologda State University, Department of Engineering Technologies;


Abstract. Introduction of digital platforms in the design phase of production preparation at medium- and small instrument-building enterprises is discussed. The process is implemented with the active use of CAD-based and CAE-based products. The tasks performed during design preparation are considered, including 3D design, engineering analysis of the structure, creation of electronic prototypes of product components as one of the factors of digital production. Results obtained in the design solution simulation concerning temperature deformations of measuring instrument units are presented.
Keywords: 3D model, digital image, manufacturing design, information environment

References:

 

1. Pasport natsional'noy programmy "Tsifrovaya ekonomika Rossiyskoy Federatsii": utv. resheniyem prezidiuma Soveta pri Prezidente RF po strategicheskomu razvitiyu i natsional'nym proyektam 24 dekabrya 2018 goda (Passport of the National Program "Digital Economy of the Russian Federation": approved by Decision of the Presidium of the Presidential Council. Strategic Development and National Project Federations, December 24, 2018). (in Russ.)

2. Piters D. SAPR i grafika (CAD and graphics), 2016, no. 1, pp. 4–7. (in Russ.)

3. Borovkov A.I., Ryabov Yu.A. XVII Aprel'skaya mezhdunarodnaya nauchnaya konferentsiya po problemam razvitiya ekonomiki i obshchestva (XVII April International Scientific Conference on the Problems of Economic and Social Development, Moscow, April 19–22, 2016), Moscow, 2017,
vol. 3, рр. 381–389. (in Russ.)

4. http://assets.fea.ru/uploads/fea/news/2017/11_november/17/tsifrovoe_proizvodstvo_112017.pdf. (in Russ.)

5. Schuh G., Anderl R., Gausemeier J., ten Hompel M., Wahlster W., eds., Managing the Digital Transformation of Companies, Munich: Herbert Utz, 2017.

6. Zil'berburg L.I., Molochnik V.I., Yablochkov E.I. Informatsionnyye tekhnologii v proyektirovanii i proizvodstve (Information Technology in Design and Production), St. Petersburg, 2008, 304 р. (in Russ.)

7. Bulavin V.F., Yakhrichev V.V., Stepanov A.S. Proceedings of Higher Educational Institutions. Маchine Building, 2019, no. 9, pp. 35–45, DOI:10.18698/0536-1044-2019-9-35-45. (in Russ.)

8. Bulavin V.F., Yakhrichev V.V., Glazkov V.A. Proceedings of Higher Educational Institutions. Маchine Building, 2018, no. 8, pp. 37–49, DOI:10.18698/0536-1044-2018-8-37-49. (in Russ.)

9. Bulavin V.F., Bulavina T.G., Yakhrichev V.V. Fundamental and Applied Problems of Technics and Technology, 2017, no. 5(325), pp. 64–72. (in Russ.)

10. Bykov A., Karabcheyev K. SAPR i grafika (CAD and graphics), 2016, no. 1, pp. 18–19. (in Russ.)

11. Bulavin V.F., Yakhrichev V.V. SAPR i grafika (CAD and graphics), 2018, no. 6, pp. 52–55. (in Russ.)

12. Volkov E.V., Kuz'mina M.S., Pomeshchikov V.E., Bulavin V.F., Grigor'yev N.S., Yakhrichev V.V. Eurasian Scientific Association, 2017, no. 10(32), pp. 65–68. (in Russ.)

13. Yakhrichev V.V., Blagovestova M.E., Kazakova S.A., Nesterova A.A., Stoletova A.N., Panchenko E.N., Gromov A.A., Bulavin V.F. Eurasian Scientific Association, 2018, no. 1(35), pp. 70–73. (in Russ.)

14. Alyamovskiy A.A. Inzhenernyye raschety v Solid Works Simulation (Engineering Calculations in Solid Works Simulation), Moscow, 2010, 464 р. (in Russ.)

15. Bulavin V.F., Bulavina T.G., Yakhrichev V.V. Fundamental and Applied Problems of Technics and Technology, 2018, no. 2(328), pp. 109–120. (in Russ.)

16. Karachev A.Yu., Bulavin V.F. Bulletin of Vologda State University Series Technical Sciences, 2018, no. 1(1), pp. 6–10. (in Russ.)

17. Nikiforov A.D., Bakiyev A.V. Protsessy zhiznennogo tsikla produktsii v mashinostroyenii (Product Life Cycle Processes in Mechanical Engineering), Moscow, 2011, 688 р. (in Russ.)