ISSN 0021-3454 (print version)
ISSN 2500-0381 (online version)
Menu

2
Issue
vol 67 / February, 2024
Article

DOI 10.17586/0021-3454-2023-66-3-241-246

UDC 658.512

METHODOLOGY FOR DESIGNING FORMING PARTS OF INJECTION MOLDS USING INFORMATION TECHNOLOGIES

M. G. Lopatov
ITMO University, Faculty of Control Systems and Robotics;


A. V. Chukichev
ITMO University, Faculty of Control Systems and Robotics;


O. S. Timofeeva
ITMO University, Department of Instrumentation Technology; Student


Read the full article 

Abstract. A method of designing forming parts of injection molds is presented. Results of analysis of the gating system parameters are presented in the form of a table of dependences on parameters of a polymer product. The obtained results can be used in the development of a knowledge base.
Keywords: technological production preparation, polymer product, injection molding, parametrization, reconfigurable injection mold

References:
  1. Markov A.M. Algoritm proyektirovaniya gruppovogo tekhnologicheskogo protsessa mekhanicheskoy obrabotki detaley (Algorithm for Designing a Group Technological Process of Machining Parts), Barnaul, 2012. (in Russ.)
  2. Mitrofanov S.P. Osobennosti gruppovoy tekhnologii mekhanicheskoy obrabotki v sovremennykh usloviyakh (Features of Group Machining Technology in Modern Conditions), St. Petersburg, 2001. (in Russ.)
  3. Barvinsky I. Polymer materials. Products, equipment, technology, 2018, no. 2, pp. 22–29. (in Russ.)
  4. Pirogov A.V. Razrabotka i modelirovaniye protsessov tekhnologicheskoy podgotovki proizvodstva izdeliy iz polimernykh opticheskikh materialov (Development and Modeling of the Processes of Technological Preparation for the Production of Products from Polymeric Optical Materials), Candidate’s thesis, St. Petersburg, 2014. (in Russ.)
  5. Gao H. Frontiers of Mechanical Engineering, 2018, vol. 13, pр. 85–95.
  6. Mok C.K., Hua M. & Wong S.Y. International Journal of Production Research, 2008, no. 14(46), pp. 3783–3800, https://doi.org/10.1080/00207540601103100.
  7. Low M., Lee K. Int. Journ. Adv. Manufac. Tech., 2003, vol. 21, рр. 807–819, https://doi.org/10.1007/s00170-002-1397-9.
  8. Basov K.I., Braginsky V.A., Kazankov Yu.V. Formuyushchiy instrument dlya izgotovleniya izdeliy iz polimernykh materialov (Forming Tool for the Manufacture of Products from Polymeric Materials), Moscow, 1991. (in Russ.)
  9. Kazmer D.O. Injection Mold Design Engineering, Hanser Publications, 553 р.
  10. Kryzhanovsky V.K. Inzhenernyy vybor i identifikatsiya plastmass (Engineering Selection and Identification of Plastics), St. Petersburg, 2009, 204 р. (in Russ.)
  11. Talapov V.V., Timofeeva O.S., Pompeev K.P. Innovatsii na transporte i v mashinostroyenii (Innovations in Transport and Mechanical Engineering), Proceedings of the IV International Scientific and Practical Conference, St. Petersburg, April 28–29, 2016, vol. 3, рр. 138–142. (in Russ.)
  12. Menges G., Michaeli W., Mohren P. How to make injection molds, Hanser Publishers, Munich, 2001.
  13. Rutkauskas Ž., Bargelis A. Mechanika, 2007, no. 4(66).